Links to ICM furnace control boards in Canada .
Here is a comprehensive list of furnace contraol boards used in gas furnaces, electric furnaces and air conditioning systems .
CSR-U1 | ICM866U | Motor Starters/Rapid Start | |
| 5.2.1 | CSR-U2/U3 | ICM866U | Motor Starters/Rapid Start |
| A-1 | EAC-501-ADJ | ICM203 | Delay On Break Timers |
| A-1 | 7061 | ICM103 | Delay On Make Timers |
| A-1 | 5893 | ICM255 | Fan Blower Controls |
| A-1 | EAC-401, 402, 403, 404 | ICM492, ICM493 | Line Voltage Monitors |
| A-1 | EAC-800, EAC-8000, EAC-8002 | ICM450A, ICM450A PLUS+ | Line Voltage Monitors |
| A-1 | EAC-8002 | ECA100-11 | Line Voltage Monitors |
| A-1 | WSX-5 | ICM855 | Motor Starters/Rapid Start |
| A-1 | WSX-6 | ICM856 | Motor Starters/Rapid Start |
| A-1 | EAC-701-ADJ | ICM102 | Delay On Make Timers |
| Abb | Ovrhldxx-120 | ICM530 | Surge Protective Device |
| Abb | Ovrhldxx-277 | ICM531 | Surge Protective Device |
| Act | Fm2000 | ICM325A | Head Pressure Controls |
| ASCO | 420120S | ICM518 | Split Phase Surge Protective Device |
| ASCO | 420120Y, 420240D | ICM530 | Surge Protective Device |
| ASCO | 420240H | ICM533 | Surge Protective Device |
| ASCO | 420277Y, 420480D | ICM531 | Surge Protective Device |
| ASCO | 420347Y, 420600D | ICM532 | Surge Protective Device |
| Bard | 8201-056 | ICM255 | Fan Blower Controls |
| Bristol | 241680 | ICM441 | Line Voltage Monitors |
| CAC | EOCR-3DM | ECA500-11 | Line Voltage Monitors |
| Carlin | 48245 | ICM1503 | Oil Burner Primary Control |
| Carlo Gavazzi | RSBS Series, Smooth Starter - SS230V1p16-32 | ICM870-32A | Soft Start |
| Carlo Gavazzi | RSmooth Starter - SS230V1p16-16 | ICM870-16A | Soft Start |
| Carrier | 325878-751 | ICM282B | Furnace/Ignition Control Boards |
| Carrier | 302075-3, Ces0110017, ces0110018 | ICM271 | Fan Blower Controls |
| Carrier | Ces0110019 | ICM275 | Fan Blower Controls |
| Carrier | Hh84aa001, hh84aa003, hh84aa005, hh84aa009, hh84aa014, hh84aa015, hh84aa021 | ICM275 | Fan Blower Controls |
| Carrier | Hh84aa010, hh84aa011, hh84aa012, hh84aa013, hh84aa020, p771-7002 | ICM271 | Fan Blower Controls |
| Carrier | Ces0110057-00, ces0110057-01, | ICM281 | Furnace/Ignition Control Boards |
| ces0110057-00 | |||
| Carrier | Ces0110020, ces0110048 | ICM281 | Furnace/Ignition Control Boards |
| Carrier | Hk42fz017 | ICM2807 | Furnace/Ignition Control Boards |
| Carrier | Hk42fz-004, hk42fz-007, hk42fz-008, hk42fz-009, hk42fz-011, hk42fz-013, hk42fz-016, hk42fz-34 | ICM282B | Furnace/Ignition Control Boards |
| Carrier | Hh84aa016 | ICM281 | Furnace/Ignition Control Boards |
| Carrier | Lh33wp003/3a | ICM291 | Furnace/Ignition Control Boards |
| Carrier | Hk42fz004, hk42fz007, hk42fz008, hk42fz009, hk42fz011, hk42fz016 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Coleman/Evcon/Lennox/Luxaire/York | G951adb-1401(c), g951adb1402, g951adb-1403, g951aeb-1403, 265901, 265902, 539617, 52537074000, 52537077000, 031-00662, 031-00662-700, 031-01250-700, 031-01266-700, 031-01284-000, 031-01973-000, 031-09166-000, 331-01933-000, 331-01972-000, 331-09167-000, s1-03100662000, s1-03101250000, s1-03101266000, s1-03101267000, s1-03101267001, s1-03101284000, s1-03101933000, s1-03101972000, s1-03101973000, s1-03109167000, s1-33102956000, s1-33103010000, | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Copeland | 071-0376-01, 071-0376-02, 071-0397-00, 071-0397-01, 071-0424-00, 071-0424-01, 071-9800-01, 071-9800-02 | ICM441 | Line Voltage Monitors |
| Copeland | 085-0160-00 | ICM450A, ICM450A PLUS+ | Line Voltage Monitors |
| Diversified | Ac-100-3 | ICM206 | Delay On Break Timers |
| Diversified | Ac-100-5 | ICM206 | Delay On Break Timers |
| Diversified | Ac-503 | ICM203 | Delay On Break Timers |
| Diversified | Ac-800 | ICM102 | Delay On Make Timers |
| Diversified | Ac-2020, ac-301, ac-302 | ICM450A, ICM450A PLUS+ | Line Voltage Monitors |
| Dometic Smart Start | 340582 | ICM870-16A | Soft Start |
| Dometic Smart Start | 340583 | ICM870-9A | Soft Start |
| Eaton | Sp1-240s, sp2-240s | ICM518 | Split Phase Surge Protective Device |
| Eaton | Sp1-208y, sp1-240d, sp2-208y, sp2-240d | ICM530 | Surge Protective Device |
| Eaton | Sp1-480y, sp1-480d, sp2-480y, sp2-480d | ICM531 | Surge Protective Device |
| Eaton | Sp1-600y, sp1-600d, ap2-600y | ICM532 | Surge Protective Device |
| Eaton | Spd050240h1 | ICM533 | Surge Protective Device |
| Erico (Critec) | Tdx50c240 | ICM518 | Split Phase Surge Protective Device |
| Erico (Critec) | Tdx50c277/480 | ICM531 | Surge Protective Device |
| Erico (Critec) | Txd50c120/208, txd50c120/240d | ICM530 | Surge Protective Device |
| Erico (Critec) | Txd50c347/600 | ICM532 | Surge Protective Device |
| Essex | Independent Relays Series 84 and 93 | ICM220 | Lockout Protection Relays |
| Evo/ecm | Vcu-36-mp | ICM708 | Ecm Controls |
| Evo™/ecm | 4spd | ICM709 | Ecm Controls |
| Evo™/ecm1 | Acu+–s1 | ICM711 | Ecm Controls |
| Fenwal | 35-725200-005 | ICM2910-200-005 | Gas Ignition Controls |
| Fenwal | 35-725201-007 | ICM2910-201-007 | Furnace/Ignition Control Boards |
| Fenwal | 35-725201-501 | ICM2910-201-501 | Furnace/Ignition Control Boards |
| Fenwal | 35-725201-505 | ICM2910-201-505 | Furnace/Ignition Control Boards |
| Fenwal | 35-725205-015 | ICM2910-205-015 | Furnace/Ignition Control Boards |
| Fenwal | 35-725205-017 | ICM2910-205-017 | Furnace/Ignition Control Boards |
| Fenwal | 35-725205-021 | ICM2910-205-021 | Furnace/Ignition Control Boards |
| Fenwal | 35-725205-115 | ICM2910-205-115 | Furnace/Ignition Control Boards |
| Fenwal | 35-725205-521 | ICM2910-205-521 | Furnace/Ignition Control Boards |
| Fenwal | 35-725206-515 | ICM2910-206-515 | Furnace/Ignition Control Boards |
| Fenwal | 35-725405-013 | ICM2910-405-013 | Furnace/Ignition Control Boards |
| Fenwal | 35-605939-337 | ICM2919 | Furnace/Ignition Control Boards |
| Fenwal | 06-236879-002 | ICM6700 | Gas Ignition Controls |
| Fenwal | 35-525900-113 | ICM6701 | Gas Ignition Controls |
| Gemline | 1c213 | ICM102, ICM103 | Delay On Make Timers |
| Gemline | 1c310 | ICM102 | Delay On Make Timers |
| Generac | G0073000 | ICM518 | Split Phase Surge Protective Device |
| Goodman | B1226008 , pcbdm101(s) | ICM318 | Defrost Controls |
| Goodman | B1370735s, pcbfm131s | ICM277 | Fan Blower Controls |
| Goodman | Pcbfm103, pcbfm103s | ICM256 | Fan Blower Controls |
| Goodman | B18099-06, b18099-08, b18099-10, b18099-13, b18099-13s | ICM280 | Furnace/Ignition Control Boards |
| Goodman | Pcbbf110/s, pcbbf123/s, 0130f00005/s, pcbbf112/s, b18099-26/s | ICM2811 | Furnace/Ignition Control Boards |
| Goodman | Pcbbf136, pcbbf140 | ICM2810 | Furnace/Ignition Control Boards |
| Goodman/Amana | 10207701, 10207704, 10207706, 10207710, 10207714, 10207717, 10207718, 10207719, 10207720, 0130f00005(s), 0130f00006(s), 102077-02, 102077-03, 102077-04, 102077-09, 10207720s, b1809926(s), pcb00109, pcbbf109, pcbbf110(s), pcbbf112(s), pcbbf122(s), pcbbf123(s), pcbbf132(s), pcbbf134, pcbbf135, pcbbf136, pcbbf138 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Goodman | Pcbab123-d | ICM2920 | Furnace/Ignition Control Boards |
| Hoffman | 880-Ecm(10)sshp | ICM713 | Ecm Controls |
| Hoffman | 800, 800a, 800aa, 814-50, 816-10 | ICM325A | Head Pressure Controls |
| Honeywell | R8184g4009, r8184g1138, r8184g1427, r8184g4025 | ICM1503 | Oil Burner Primary Control |
| Honeywell | R8184g4066, r8184g1161, r8184g1294 | ICM1501 | Oil Burner Primary Control |
| Honeywell | R8184g4074, r8184g1179, r8184g1302, r8184g4033 | ICM1502 | Oil Burner Primary Control |
| Honeywell | Th6110d1005, th6110d1021 | SC5010 | Thermostats (7-Day Programmable) |
| Honeywell | Th6220d1002, th6220d1028 | SC5811 | Thermostats (7-Day Programmable) |
| Honeywell | T8600d2028, th4110d1007, th2110d1099 | SC5010 | Thermostats (7-Day Programmable) |
| Honeywell | T8400, t8401 series | SC2010L | Thermostats (Non-Programmable) |
| Honeywell | T8775a1009, th1100d1001 | SC1600L | Thermostats (Non-Programmable) |
| Honeywell | Th1110d1000, th3110d1008 | SC2010L | Thermostats (Non-Programmable) |
| Honeywell | S8610u | ICM2918 | Gas Ignition Controls |
| Hyper Engineering | Sure Start | ICM870-9A/16A/32A | Soft Start |
| Ice-o-matic | Td3001a | ICM103 | Delay On Make Timers |
| Icm | W1001-4 | ICM318 | Defrost Controls |
| Icp | 1171166 | ICM291 | Furnace/Ignition Control Boards |
| Icp | 1176943 | ICM282B | Furnace/Ignition Control Boards |
| Iec | E025-71521506 | ICM712 | Ecm Controls |
| Intermatic | Ag3000 | ICM517A | Single Phase Surge Protection |
| Intermatic | Ag2401c3, ig1200rc3, ig1240rc3, ig3240rc3 | ICM518 | Split Phase Surge Protective Device |
| Intermatic | Ag2403c3, l5f13d1dg1 | ICM533 | Surge Protective Device |
| Intermatic | Ag4803c3, l5f13y2dg1 | ICM531 | Surge Protective Device |
| Intermatic | Ag6503, l5f13y3dg1 | ICM532 | Surge Protective Device |
| Intermatic | Ag2083c3 l5f13y1dg1 | ICM530 | Surge Protective Device |
| Intermatic/Grasslin | 010-0011b, dt040, dt140, dtav40, dtav40m, dt-b, dtmv, dtsx | ICM550, ICM550-ENC | Defrost Controls |
| Intermatic/Grasslin | 010-0011b, dt040, dt140, dtav40, dtav40m, dt-b, dtmv, dtsx | ICM550, ICM550-ENC | Multi–Functional Timers |
| Jackson Systems | Cl-45, cl-55, cl-75 (cool) | ACH045, ACH055, ACH075 | Thermostats (Temporary) |
| Jackson Systems | Ts-60, ts-65 & ts-70 (heat) | ACH060, ACH065, ACH070 | Thermostats (Temporary) |
| Johnson Controls | P66bab/bad | ICM325A (for 2 temp or 2 pres inputs) | Head Pressure Controls |
| Kickstart | Ks1 | ICM866U | Motor Starters/Rapid Start |
| Kickstart | To5, ks8 | ICM866U | Motor Starters/Rapid Start |
| Lennox | All bcc1, bcc2, bcc3 Circuit Borads, Including 48k98 | ICM289 | Furnace/Ignition Control Boards |
| Lennox | 10m9301, 12l6901, 32m8801, 56l8401, 24l8501, 63k8901, 97l4801, 100925-01, 100925-03, 17w9201, 23w5101, 30w2501, 69m0801, 69m1501, 83m00 | ICM2813 | Furnace/Ignition Control Boards |
| Lennox | 1214201, 100925 (-01,-02,-03), 10m93, 10m9301, 12l6901, 17w92, 17w9201, 23w51, 23w5101, 30w25, 30w2501, 32m8801, 56l84, 56l8401, 69m08, 69m0801, 69m15, 69m1501, x4459, x445901, | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Leviton | 55240-Asa | ICM518 | Split Phase Surge Protective Device |
| Leviton | 55208-Asa | ICM530 | Surge Protective Device |
| Leviton | 55480-Asa | ICM531 | Surge Protective Device |
| Mars | 32395 | ICM175 | Bypass Timers |
| Mars | 32001, 32387, 32392 | ICM203 | Delay On Break Timers |
| Mars | 32382 | ICM206 | Delay On Break Timers |
| Mars | 32019, 32391, 32367 | ICM102 | Delay On Break Timers |
| Mars | 32394, 32396 | ICM103 | Delay On Break Timers |
| Mars | 32574 | ICM255 | Fan Blower Controls |
| Mars | 32536 | ICM401A, ICM402 | Line Voltage Monitors |
| Mars | 37300, 37302, 37304, 37306, 37322 | ICM441 | Motor Protection |
| Mars | Pfm-2000 | ICM450A | Line Voltage Monitors |
| Mars | 83916 | ICM495-30A | Surge Protective Device |
| Mars | 83915 | ICM495-60A | Surge Protective Device |
| Mars | 32702, 35702 | ICM856 | Motor Starters/Rapid Start |
| Mars | 32781 | ICM857 | Motor Starters/Rapid Start |
| Mars | 83905 | ICM518 | Split Phase Surge Protective Device |
| Mars | 32701, 35701 | ICM855 | Motor Starters/Rapid Start |
| Micro-Air | Easy Start | ICM870-9A/16A/32A | Soft Start |
| Mitsubishi | Mu09nw, muh09nw, mu12nn, mu15nn, mu17nn, mum18nw, mum30nn, mum30nn2 | ICM325A | Head Pressure Controls |
| Modine | 5h79749 | ICM2911 | Furnace/Ignition Control Boards |
| Motorsaver | 455 | ICM450A, ICM450A PLUS+ | Line Voltage Monitors |
| Nassar | PM-31 | ECA500-11 | Line Voltage Monitors |
| N/a | N/a | ICM6202 | Fan Coil Relay Control Boards |
| Network RV | Soft Start | ICM870-9A/16A | Soft Start |
| Nordyne | 624631 | ICM2805A | Furnace/Ignition Control Boards |
| Nordyne | 624557, 624564, 624591, 624628, 902378, 902696, 903106, 624631(A), 624631(a), 710128a, | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Paragon | 8041, 8045, 8047, 8141, 8143, 8145, 8245, 8247 | ICM550, ICM550-ENC | Defrost Controls |
| Paragon | 8041, 8045, 8047, 8141, 8143, 8145, 8245, 8247 | ICM550, ICM550-ENC | Multi–Functional Timers |
| Precision | 6041, 6045, 6047, 6141, 6145 | ICM550, ICM550-ENC | Defrost Controls |
| Precision | 6041, 6045, 6047, 6141, 6145 | ICM550, ICM550-ENC | Multi–Functional Timers |
| Qwik products | Qwikswapx1 | ICM715 | Ecm Controls |
| Qwik Products | Qwikswapx3 | ICM716 | Ecm Controls |
| Ranco | E31 | ICM325A | Head Pressure Controls |
| RectorSeal | RSH-50 96417 | ICM495-30A | Surge Protective Device |
| RectorSeal | RSH-50 96419 | ICM495-60A | Surge Protective Device |
| Reznor | 195265 | ICM2907 | Gas Ignition Controls |
| Reznor | 257009 | ICM2904 | Gas Ignition Controls |
| Reznor | 257010 | ICMv2905 | Gas Ignition Controls |
| Reznor | 195573 | ICM2906 | Gas Ignition Controls |
| Rheem | 62-23599-01, 62-23599-02, 62-23599-03, 62-23599-04, 62-23599-05 | ICM2909 | Furnace/Ignition Boards |
| Rheem | 1157-100, 1157-110, 1157-120, 1157-121, 47-102684-01, 47-102684-02, 47-102684-03, 47-102684-04, 47-102684-08, 47-102685-02, 47-102685-04, 47-102685-05, 47-102685-06 47-102685-07, 47-21517-22, Ddl-122131-2rh | ICM3000 | Demand Defrost Controls |
| Rheem | 42-22515-01, 42-22515-02, 42-22515-03 | ICM255 | Fan Blower Controls |
| Rheem | 1157-100, 1157-110, 1157-120, 1157-121, 47-102684-01, 47-102684-02, 47-102684-03, 47-102684-04, 47-102684-08, 47-102685-02, 47-102685-04, 47-102685-05, 47-102685-06, 47-102685-07, 47-21517-22, Ddl-122131-2rh | ICM3000 | Defrost Controls |
| Rheem | 62-24140-04 | ICM292A | Furnace/Ignition Control Boards |
| Rheem | 62-24084-82 | ICM288 | Furnace/Ignition Control Boards |
| Rheem/Ruud | 695-200, 62-22694-Xx, 62-22732-xx, 62-24044-xx, 62-24045-01, 62-24046-01, 62-24084-82, 62-24268 (-01,-02,-03) | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Robertshaw | 3310-072 | ICM203 | Delay On Break Timers |
| Robertshaw | 3310-183 | ICM206 | Delay On Break Timers |
| Robertshaw | 3310-305 | ICM206 | Delay On Break Timers |
| Robertshaw | 3310-068 | ICM103 | Delay On Break Timers |
| Robertshaw | 695-100 | ICM271 | Fan Blower Controls |
| Robertshaw | 695-101 | ICM275 | Fan Blower Controls |
| Robertshaw | 8625-1 | ICM518 | Split Phase Surge Protective Device |
| Robertshaw | 300-229, 9615 | SC5811 | Thermostats (7-Day Programmable) |
| Robertshaw | 8625-1 | SC5811 | Thermostats (7-Day Programmable) |
| Robertshaw | Rs5110, rs6110 | SC5010 | Thermostats (7-Day Programmable) |
| Robertshaw | 300-206 | SC2010L | Thermostats (Non-Programmable) |
| Robertshaw | 300-204 | SC1600L | Thermostats (Non-Programmable) |
| Robertshaw | 8400-1, 9400, 9500, Rs2110 | SC2010L | Thermostats (Non-Programmable) |
| Robertshaw | 300-229, 9615 | ICM518 | Split Phase Surge Protective Device |
| Schneider Square | Motor Logic Plus 9065 | ECA500-11 | Line Voltage Monitors |
| SEL | 701 | ECA500-11 | Line Voltage Monitors |
| Siemens | Tps3b | ICM533 | Surge Protective Device |
| Siemens | Tps3d, tps3c | ICM530 | Surge Protective Device |
| Siemens | Tps3e, tps3f | ICM531 | Surge Protective Device |
| Siemens | Tps3l, tps3g | ICM532 | Surge Protective Device |
| Siemons | Tps3a | ICM518 | Split Phase Surge Protective Device |
| Snyder General/icp | 1395336 | ICM255 | Fan Blower Controls |
| Square D | Sdsa2040, sdsa2040d | ICM530 | Surge Protective Device |
| Square D | Sdsa2040d | ICM533 | Surge Protective Device |
| Square D | Sdsa3650, sdsa3650d | ICM532 | Surge Protective Device |
| Square D | Sdsa4040, sdsa4040d | ICM531 | Surge Protective Device |
| Ssac | Qlm, qlv | ICM450A, ICM450A PLUS+ | Line Voltage Monitors |
| Suburban | 35-533900-113, 521099 | ICM6700 | Furnace/Ignition Control Boards |
| Suburban | 35-533900-113, 520814 | ICM6701 | Furnace/Ignition Control Boards |
| Suburban | 521099, 35-533900-113 | ICM6700 | Gas Ignition Controls |
| Suburban | 35-525900-113, 520814 | ICM6701 | Gas Ignition Controls |
| Supco | Td32 | ICM175 | Bypass Timers |
| Supco | Td72, td73 | ICM203 | Delay On Break Timers |
| Supco | Td73w | ICM203F | Delay On Break Timers |
| Supco | Td74 | ICM206 | Delay On Break Timers |
| Supco | Tl243 | ICM206 | Delay On Break Timers |
| Supco | Tl245 | ICM206 | Delay On Break Timers |
| Supco | Td69 | ICM102 | Delay On Make Timers |
| Supco | Td69w | ICM102F | Delay On Make Timers |
| Supco | Tmf-19, tmf-80 | ICM103 | Delay On Make Timers |
| Supco | Tpmp2 | ICM401A, ICM402 | Line Voltage Monitors |
| Supco | Spp-5 | ICM855 | Motor Starters/Rapid Start |
| Supco | Spp-5e | ICM866U | Motor Starters/Rapid Start |
| Supco | Spp-6 | ICM856 | Motor Starters/Rapid Start |
| Supco | Spp-6e | ICM866U | Motor Starters/Rapid Start |
| Supco | Rco210 | ICM859 | Motor Starters/Rapid Start |
| Supco | Rco410 | ICM858 | Motor Starters/Rapid Start |
| Supco | Rco810 | ICM857 | Motor Starters/Rapid Start |
| Supco | Scmplus, scm150 | ICM517A | Single Phase Surge Protection |
| Supco | Supr, apr5 | UMSR50 | Universal Motor Starting Relays |
| Supco | Spp-8, spp-8e | ICM866U | Motor Starters/Rapid Start |
| SymCom | 601, 601-575, 455, 455-575, 455-480R | ECA100-11 | Line Voltage Monitors |
| SymCom/MotorSaver | 777 Series, 520CS-115, 520CP | ECA500-11 | Line Voltage Monitors |
| Telemecanique | LT6 | ECA500-11 | Line Voltage Monitors |
| Texas Instruments | 41f-5 | ICM280 | Furnace/Ignition Control Boards |
| Texas Instruments | 15aa1600b, 15aa1600c, 15aa1603b, 15aa1603c, 31aa1600e, 31aa1606e | ICM441 | Motor Protection |
| Texas Instruments | 41f-5, 61f3, 6dt(-1,-2), 350486, 350836 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Time Mark | 265 | ICM450A, ICM450A PLUS+ | Line Voltage Monitors |
| Time Mark | 274, 2744, 272, 2722 | ECA100-11 | Line Voltage Monitors |
| Time Mark | 2742 | ECA500-11 | Line Voltage Monitors |
| Trane | D330927p01, d330930p01, d330934p01, d340035p01, d340774p01, d341213p01, d341396p01 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Trane | D674711p01 | ICM2913 | Furnace/Ignition Control Boards |
| Trane | D674712p01 | ICM2914 | Furnace/Ignition Control Boards |
| Trane | D674713p01 | ICM2915 | Furnace/Ignition Control Boards |
| Trane | D674712p02 | ICM2916 | Furnace/Ignition Control Boards |
| Trane/American Standard | Cnt02789, cnt02891, cnt03076, cnt03798, cnt03799, cnt05164, cnt05165, d341122p01, d341235p01, d341235p03, d341396p04, d341396p05, d34139p03 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| United tch | 1003-638a | ICM2904 | Gas Ignition Controls |
| United tch | 1003-514 | ICM2905 | Gas Ignition Controls |
| United tch | 1097-211 | ICM2906 | Gas Ignition Controls |
| United tch | 1097-210 | ICM2907 | Gas Ignition Controls |
| United Technologies | 1012-83-9336a, 1012-83-9337a, 1012-925 (a,b,c), 1012-933d | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Utec | 1012-933d | ICM280 | Furnace/Ignition Control Boards |
| Wagner | DTP-3 | ECA100-11 | Line Voltage Monitors |
| Wagner/Diversitech | Adb-1 | ICM203 | Delay On Break Timers |
| Wagner/Diversitech | Adb-2 | ICM203F | Delay On Break Timers |
| Wagner/Diversitech | Adm-1 | ICM102 | Delay On Make Timers |
| Wagner/Diversitech | Adm-2 | ICM102F | Delay On Make Timers |
| Wagner/Diversitech | Dsp-1 | ICM492 | Line Voltage Monitors |
| Wagner/Diversitech | Dsp-1 | ICM493 | Line Voltage Monitors |
| Wagner/Diversitech | Dtp-3, wpc-800 | ICM450A, ICM450A PLUS+ | Line Voltage Monitors |
| Wagner/Diversitech | Dst-5 | ICM855 | Motor Starters/Rapid Start |
| Wagner/Diversitech | Dst-6 | ICM856 | Motor Starters/Rapid Start |
| Whirlpool | 8068142, 8068561, 8068563, 99958174, 99958175 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| White Rodgers | 47d43-101-90, 47d43-111-01, 47d43-111-02, 47d43-111-03, 47d43-111-04, 47d43-811 | ICM3000 | Defrost Controls |
| White Rodgers | 47d43-101-90, 47d43-111-01, 47d43-111-02, 47d43-111-03, 47d43-111-04, 47d43-811 | ICM3000 | Demand Defrost Controls |
| White Rodgers | 50a55-743, 50a55-289, 50t55-289 | ICM2811 | Furnace/Ignition Control Boards |
| White-Rodgers | 50a65-120, 50a65-121, 50a62-120, 50a62-121, 50a62-820, 21d83m-843, 50a66-122, 50a66-123 | ICM2813 | Furnace/Ignition Control Boards |
| White-Rodgers | 50m56u-843 | ICM2812, ICM2812-KIT | Furnace/ignition control boards |
| White-Rodgers | 50t35-730, 50t35-743 | ICM280 | Furnace/Ignition Control Boards |
| White-Rodgers | 668-401 | ICM1503 | Oil Burner Primary Control |
| White-Rodgers | 1f80-0471, 1f80-0671, 1f97-1277 | SC5010 | Thermostats (7-Day Programmable) |
| White-Rodgers | 1f81-261, 1f85-0422 | SC5811 | Thermostats (7-Day Programmable) |
| White-Rodgers | 1f86-344, 1f86-0244 | SC2010L | Thermostats (Non-Programmable) |
| White-Rodgers | Mechanical 1f30-321, 1c20-102 | SC1600L | Thermostats (Non-Programmable) |
| White-Rodgers | 50a50-110, 50a50-111, 50a50-112, 50a50-113, 50a50-130, 50a50-131, 50a50-142, 50a50-143, 50a50-205, 50a50-206, 50a50-207, 50a50-208, 50a50-209, 50a50-210, 50a50-215, 50a50-216, 50a50-229, 50a50-230, 50a50-240, 50a50-241, 50a50-245, 50a50-285, 50a50-286, 50a50-288, part number, 50a50-295, 50a50-296, 50a50-298, 50a50-405, 50a50-406, 50a50-407, 50a50-408, 50a50-438, 50a50-471, 50a50-472, 50a50-473, 50a50-474, 50a50-475, 50a50-571, 50a55-143, 50a55-241, 50a55-245, 50a55-250, 50a55-285, 50a55-286, 50a55-288, 50a55-289, 50a55-3797, 50a55-438, 50a55-474, 50a55-476, 50a55-480, 50a55-486, 50a55-571, 50a55-743, 50a55-843, 50a56-242, 50a56-243, 50a56-956, 50a65-120, 50a65-121, 50a65-143, 50a65-288, 50a65-289, 50a65-474, 50a65-475, 50a65-476, 50a65-5165, 50a65-843, 50a66-122, 50a66-123, 50a66-743, 50m56-281, 50m56-289, 50m56-291, 50m56-743, 50t35-730, 50t35-743, 50t55-288, 50t55-289 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| Camstat | Ipi-24-00 | ICM2918 | Ignition Control Module (Universal) |
| Fenwal | 05-203025-005, 05-203026-005 | ICM2918 | Ignition Control Module (Universal) |
| Honeywell | S8610u, s86a1001, s86a1019, s86a1027, s86a1035, s86b1009, s86b1017, s86b1025, s86c1007, s86c1015, s86c1031, s86c1049, s86c1056, s86d1005, s86d1021, s86e1002, s86e1010, s86e1028, s86e1036, s86e1044, s86e1051, s86e1069, s86e1077, s86e1101, s86e1119, s86e1127, s86f1000, s86f1018, s86f1026, s86f1042, s86f1059, s86f1067, s86f1075, s86f1083, s86f1091, s86g1008, s86g1016, s86g1032, s86g1057, s86g1073, s86h1006, s86h1022, s86h1048, s86h1089, s86h1097, s86h1105, s86h1121, s86h1147, s90a1005, s90b1003, s90b1011, s8600a1001, s8600b1009, s8600c1015, s8600f1000, s8600f1034, s8600f1042, s8600h1006, s8600h1022, s8600h1048, s8600h1055, s8600h1089, s8600h1105, s8600m1005, s8600m1013, s8610a1009, s8610b1007, s8610b1015, s8610c1005, s8610f1008, s8610f1016, s8610f1024, s8610f1032, s8610h1012, s8610h1038, s8610h1046, s8610h1053, s8610h1079, s8610m1003, s8610m1029, s8620h1028 | ICM2918 | Ignition Control Module (Universal) |
| Hsc | 1003-3, 1003-300 | ICM2918 | Ignition Control Module (Universal) |
| Penn-Johnson | Csa35a-617r, csa35a-618r, csa42a-600r, csa42a-601r, csa42a-603r, csa42a-604r, csa43a-600r, csa44a-600r, csa45a-601r, csa45a-602r, csa46a-600r, csa48a-600r, csa49a-600r, csa49a-605r, csa51a-601r, csa52a-600r, g60aaa-1, g60aag-1, g60aag-3, g60aag-4, g60aag-5, g60aag-6, g60caa-1, g60caa-3, g60cag-1, g60cag-2, g60cag-3, g60cag-4, g60cag-5, g60cag-6, g60cag-7, g60cag-8, g60cag-9, g60cba-1, g60cba-3, g60cbg-1, g60cbg-10, g60cbg-11, g60cbg-14, g60cbg-16, g60cbg-17, g60cbg-3, g60cbg-4, g60cbg-9, g60cca-1, g60ccg-1, g60cpg-1, g60dbg-1, g60dcg-1, g60dcg-2, g60pag-1, g60pag-2, g60pag-3, g60pag-4, g60pag-5, g60pag-6, g60paj-1, g60pak-1, g60pak-2, g60pfh-1, g60pfh-2, g60pfl-1, g60pfq-1, g60pvl-1, g60qag-2, g60qag-3, g60qak-1, g60qbg-1, g60qbg-2, g60qbg-3, g60qbg-4, g60qbg-5, g60qbg-6, g60qbg-7, g60qbg-8, g60qbg-9, g60qbh-1, g60qbk-1, g60qbk-3, g60qbl-1, g60qbl-2, g60qcg-1, g60qcj-1, g60qcl-1, g60qdg-1, g60qfl-1, g60qhl-1, g60qjl-1, g60qlg-1, g60qpl-1, g60qrh-1, g60qrl-1, g60qrl-2, g60qrl-3, g60qsl-1, g60qth-1, g60qtl-1, g60rag-1, g60rak-1, g60rbg-1, g60rbg-2, g60rbg-3, g60rbk-1, g60rbk-2, g60rcg-2, g60rcj-1, g60rdg-1, g60rdk-1, g60rgl-1, g60rhl-1, g60rhp-1, g60rpl-1, g60rsl-1, g60zag-1, g65bbg-1, g65bbg-2, g65bbg-3, g65bbg-4, g65bbg-5, g65bbg-6, g65bbg-7, g65bbg-8, g65bbm-1, g65bbm-2, g65bbm-3, g65bbm-4, g65bcg-1, g65bcm-1, g65bfg-1, g65bfm, g65bkg-1, g65bkg-2, g65bkg-3, g65bkm-1, g65bkm-2, g65bkm-3, g65dbg, g65dbm-1, g65dbm-3, g65dcm-1, g65dfg, g65dfm-1, g65dkg, g65dkm, g65fbg, g65ffg, g65fkg, g66ag-1, g66bg-1, g66mg-1, g66ng-1, g67ag-3, g67ag-4, g67ag-7, g67ag-8, g67bg-2, g67bg-3, g67bg-4, g67bg-5, g67mg-1, g67mg-4, g67ng-2, g600ax-1, g600ay-1, g600mx-1, g600nx-1, g600rx-1, g670aw-1, g770mga-1, g770mga-2, g770mgc-1, g770mgc-2, g770mgc-3, g770mha-1, g770nga-1, g770ngc-4, g770ngc-5, g770ngc-6, g770ngc-7, g770rga-1, g770rha-1, g770mha-2, g770mhc-1, g770nha-1, g770nhc-1, g770rha-2 | ICM2918 | Ignition Control Module (Universal) |
| Robertshaw | 780-715, 780-735, 780-737, Sp715, sp715a, sp735, sp735d, sp735l, usi 715u | ICM2918 | Ignition Control Module (Universal) |
| White-Rodgers | 50M56U-843 | ICM2812, ICM2812-KIT | Furnace/Ignition Control Boards |
| White-Rodgers | 50T35-730, 50T35-743 | ICM280 | Furnace/Ignition Control Boards |
| White-Rodgers | 668-401 | ICM1503 | Oil Burner Primary Control |
| White-Rodgers | 1F80-0471, 1F80-0671, 1F97-1277 | SC5010 | Thermostats (7-Day Programmable) |
| White-Rodgers | 1F81-261, 1F85-0422 | SC5811 | Thermostats (7-Day Programmable) |
| White-Rodgers | 1F86-344, 1F86-0244 | SC2010L | Thermostats (Non-Programmable) |
| White-Rodgers | Mechanical 1F30-321, 1C20-102 | SC1600L | Thermostats (Non-Programmable) |
| White-Rodgers | 50A50-110, 50A50-111, 50A50-112, 50A50-113, 50A50-130, 50A50-131, 50A50-142, 50A50-143, 50A50-205, 50A50-206, 50A50-207, 50A50-208, 50A50-209, 50A50-210, 50A50-215, 50A50-216, 50A50-229, 50A50-230, 50A50-240, 50A50-241, 50A50-245, 50A50-285, 50A50-286, 50A50-288, Part Number, 50A50-295, 50A50-296, 50A50-298, 50A50-405, 50A50-406, 50A50-407, 50A50-408, 50A50-438, 50A50-471, 50A50-472, 50A50-473, 50A50-474, 50A50-475, 50A50-571, 50A55-143, 50A55-241, 50A55-245, 50A55-250, 50A55-285, 50A55-286, 50A55-288, 50A55-289, 50A55-3797, 50A55-438, 50A55-474, 50A55-476, 50A55-480, 50A55-486, 50A55-571, 50A55-743, 50A55-843, 50A56-242, 50A56-243, 50A56-956, 50A65-120, 50A65-121, 50A65-143, 50A65-288, 50A65-289, 50A65-474, 50A65-475, 50A65-476, 50A65-5165, 50A65-843, 50A66-122, 50A66-123, 50A66-743, 50M56-281, 50M56-289, 50M56-291, 50M56-743, 50T35-730, 50T35-743, 50T55-288, 50T55-289 | ICM2812-KIT | Furnace/Ignition Control Boards (Universal) |
| White-Rodgers | 90-621 | ICM300 | Defrost Controls |
| York | S1-331-03010000, S1-331-02956000 | ICM2808 | Furnace/Ignition Control Boards |
| York | 7990-319P | ICM2801 | Furnace/Ignition Control Boards |
| Fenwal | 05-203025-005, 05-203026-005 | ICM2918 | Ignition Control Module (Universal) |
| Honeywell | S8610U, S86A1001, S86A1019, S86A1027, S86A1035, S86B1009, S86B1017, S86B1025, S86C1007, S86C1015, S86C1031, S86C1049, S86C1056, S86D1005, S86D1021, S86E1002, S86E1010, S86E1028, S86E1036, S86E1044, S86E1051, S86E1069, S86E1077, S86E1101, S86E1119, S86E1127, S86F1000, S86F1018, S86F1026, S86F1042, S86F1059, S86F1067, S86F1075, S86F1083, S86F1091, S86G1008, S86G1016, S86G1032, S86G1057, S86G1073, S86H1006, S86H1022, S86H1048, S86H1089, S86H1097, S86H1105, S86H1121, S86H1147, S90A1005, S90B1003, S90B1011, S8600A1001, S8600B1009, S8600C1015, S8600F1000, S8600F1034, S8600F1042, S8600H1006, S8600H1022, S8600H1048, S8600H1055, S8600H1089, S8600H1105, S8600M1005, S8600M1013, S8610A1009, S8610B1007, S8610B1015, S8610C1005, S8610F1008, S8610F1016, S8610F1024, S8610F1032, S8610H1012, S8610H1038, S8610H1046, S8610H1053, S8610H1079, S8610M1003, S8610M1029, S8620H1028 | ICM2918 | Ignition Control Module (Universal) |
| Camstat | IPI-24-00 | ICM2918 | Ignition Control Module (Universal) |
| HSC | 1003-3, 1003-300 | ICM2918 | Ignition Control Module (Universal) |
| Penn-Johnson | CSA35A-617R, CSA35A-618R, CSA42A-600R, CSA42A-601R, CSA42A-603R, CSA42A-604R, CSA43A-600R, CSA44A-600R, CSA45A-601R, CSA45A-602R, CSA46A-600R, CSA48A-600R, CSA49A-600R, CSA49A-605R, CSA51A-601R, CSA52A-600R, G60AAA-1, G60AAG-1, G60AAG-3, G60AAG-4, G60AAG-5, G60AAG-6, G60CAA-1, G60CAA-3, G60CAG-1, G60CAG-2, G60CAG-3, G60CAG-4, G60CAG-5, G60CAG-6, G60CAG-7, G60CAG-8, G60CAG-9, G60CBA-1, G60CBA-3, G60CBG-1, G60CBG-10, G60CBG-11, G60CBG-14, G60CBG-16, G60CBG-17, G60CBG-3, G60CBG-4, G60CBG-9, G60CCA-1, G60CCG-1, G60CPG-1, G60DBG-1, G60DCG-1, G60DCG-2, G60PAG-1, G60PAG-2, G60PAG-3, G60PAG-4, G60PAG-5, G60PAG-6, G60PAJ-1, G60PAK-1, G60PAK-2, G60PFH-1, G60PFH-2, G60PFL-1, G60PFQ-1, G60PVL-1, G60QAG-2, G60QAG-3, G60QAK-1, G60QBG-1, G60QBG-2, G60QBG-3, G60QBG-4, G60QBG-5, G60QBG-6, G60QBG-7, G60QBG-8, G60QBG-9, G60QBH-1, G60QBK-1, G60QBK-3, G60QBL-1, G60QBL-2, G60QCG-1, G60QCJ-1, G60QCL-1, G60QDG-1, G60QFL-1, G60QHL-1, G60QJL-1, G60QLG-1, G60QPL-1, G60QRH-1, G60QRL-1, G60QRL-2, G60QRL-3, G60QSL-1, G60QTH-1, G60QTL-1, G60RAG-1, G60RAK-1, G60RBG-1, G60RBG-2, G60RBG-3, G60RBK-1, G60RBK-2, G60RCG-2, G60RCJ-1, G60RDG-1, G60RDK-1, G60RGL-1, G60RHL-1, G60RHP-1, G60RPL-1, G60RSL-1, G60ZAG-1, G65BBG-1, G65BBG-2, G65BBG-3, G65BBG-4, G65BBG-5, G65BBG-6, G65BBG-7, G65BBG-8, G65BBM-1, G65BBM-2, G65BBM-3, G65BBM-4, G65BCG-1, G65BCM-1, G65BFG-1, G65BFM, G65BKG-1, G65BKG-2, G65BKG-3, G65BKM-1, G65BKM-2, G65BKM-3, G65DBG, G65DBM-1, G65DBM-3, G65DCM-1, G65DFG, G65DFM-1, G65DKG, G65DKM, G65FBG, G65FFG, G65FKG, G66AG-1, G66BG-1, G66MG-1, G66NG-1, G67AG-3, G67AG-4, G67AG-7, G67AG-8, G67BG-2, G67BG-3, G67BG-4, G67BG-5, G67MG-1, G67MG-4, G67NG-2, G600AX-1, G600AY-1, G600MX-1, G600NX-1, G600RX-1, G670AW-1, G770MGA-1, G770MGA-2, G770MGC-1, G770MGC-2, G770MGC-3, G770MHA-1, G770NGA-1, G770NGC-4, G770NGC-5, G770NGC-6, G770NGC-7, G770RGA-1, G770RHA-1, G770MHA-2, G770MHC-1, G770NHA-1, G770NHC-1, G770RHA-2 B659 | ICM2918 | Ignition Control Module (Universal) |
| Robertshaw | 780-715, 780-735, 780-737, SP715, SP715A, SP735, SP735D, SP735L, USI 715U | ICM2918 | Ignition Control Module (Universal) |
| Furnace control boards Canada, | |||
| Hot Surface Ignition (HSI) control board Microprocessor-based Monitors timing, trial for ignition, system switches, flame sensing and lockout. 100% lockout safety feature Compatible with LP or Natural Gas LED indication for status and fault codes to aid in troubleshooting ICM2812 includes a replacement board only ICM2812-KIT includes cable harnesses for compatibility with more than 150 furnace control boards INTRODUCTION The ICM2812 has incorporated LED diagnostics to assist in troubleshooting. Fault code information can be found in this application guide. Please keep this application guide with the furnace installation manual for future reference. SAFETY CONSIDERATIONS Only trained personnel should install or service heating equipment. When working with heating equipment, be sure to read and understand all precautions in the documentation, on labels, and on tags that accompany the equipment. Failure to follow all safety guidelines may result in damage to equipment, severe personal injury or death. SPECIFICATIONS Control voltage: 24 VAC (18-30 VAC), 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40˚to 175˚F (-40˚to 80˚C) OUTPUTS HSI Hot Surface Ignitor: 6 amp @ 120 VAC Gas Valve: 1.5 amp @ 24 VAC Inducer draft motor: 2.2 FLA @ 120 VAC Blower motor: 9.5 FLA @ 120 VAC REPLACES See pages at end of this instruction. ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS Use caution when installing and servicing the furnace to avoid and control electrostatic discharge; ESD can impact electronic components. These precautions must be followed to prevent electrostatic discharge from hand tools and personnel. Following the precautions will protect the control from ESD by discharging static electricity buildup to ground. CAUTION! Disconnect all power to the furnace. Do not touch the control or the wiring prior to discharging your body’s electrostatic charge to ground. To ground yourself, touch your hand and tools to a clean, metal (unpainted) furnace surface near the control board. Service the furnace after touching the chassis. Your body will recharge with static electricity as you shuffle your feet or move around, and you must reground yourself. Reground yourself if you touch ungrounded items. Before handling a new control, reground yourself, this will protect the control. Store the used and new controls in separate; containers before touching ungrounded objects. ESD damage can also be prevented by using an ESD service kit. CAUTION: To service control, and prior to disconnection, label all wires. Failure to do so may result in wiring errors that can cause dangerous operation. REMOVE EXISTING CONTROL Turn thermostat to OFF position or set it to the lowest possible setting. Turn OFF electrical supply to furnace. Turn OFF gas supply to furnace. CAUTION: Failure to turn off gas and electric supplies can result in explosion, fire, death, or personal injury. Remove furnace blower and control access doors. Disconnect thermostat wires and humidifier wires (if equipped with a humidifier). Disconnect line voltage, blower, electronic air cleaner wires (if equipped), and transformer wires. Remove screws and any other fasteners, and the old circuit board. Examine control and control box to check for water stains. Make repairs if any sources of water leakage are found. Be sure to check humidifiers, evaporator coils, and vent systems in the area of the control. INSTALL NEW CONTROL Ground yourself. When handling circuit board, hold it by the edges. Fasten circuit board with retaining screws. Connect all line voltage, low voltage, and accessory wires. Verify the sequence of operation. SEQUENCE OF OPERATION On the application of power, the ICM2812 will continuously monitor the rollout switch, limit switch, pressure switch, gas valve output and flame sense. During a Call for Heat, the control makes sure the limit switch is closed and the pressure switch contact is open before turning on the Inducer blower, which will be energized for the 30-second pre-purge. Following the pre-purge period, the pressure switch contact is closed and power is applied to the hot surface ignitor (there is a 19-second warm-up period), both gas valves are energized. Once flame is established and sensed the ignitor is turned off. 1STG (Single Stage): After the 30 seconds heat blower on delay the high (HI HEAT-H) speed is energized. 2STG (Dual Stage): After 5 seconds the high gas valve (MV HI) is turned off. The low (LO HEAT-H) speed blower will energize after the 30 seconds heat blower on delay. The ICM2812 will switch to second stage heat after 5 minutes of continuous operation; the high gas valve (MV HI) is re-energized along with the low gas valve (MV LO) and the main blower will switch to the high (HI HEAT-H) speed for the duration of the heat call. Once the heat call is satisfied; the blower is switched to the low (LO HEAT-H) speed; the Inducer Draft motor turns off after the 25 second post purge delay and the blower motor turns off after the preselected heat blower off delay of either 100 or 150 seconds. Fan: A fan call from the thermostat will energize the blower motor without delay at low (LO HEAT-H) speed. The blower is turned off without delay when the Fan call is removed. Cooling: A cooling call from the thermostat will energize the blower motor at high (COOL-H) speed after the 6 second cool blower on delay. The blower is turned off 45 seconds after the cooling call is satisfied. FLAME SENSE TROUBLESHOOTING TIPS Flame not established If flame is not established during the 4 second initial sequence then the control will start the next trial for ignition in 60 seconds. There will be 2 more attempts to ignite after the 60 seconds delay, before the respective fault code is triggered and the ignition trials are stopped. If flame has not been established after the 3 trials for ignition; the control will enter a 60 minute soft lockout and flash the respective fault code. The lockout can be cleared by cycling the W call or the input power. The blower motor is off until 30 seconds after flame is established and sensed. Flame out Flame out is considered when flame is lost during heating. When a W signal is present and flame is not sensed, then gas valve will disengage until the next trial for ignition. If flame is not established on the immediate sequence (2 above) then the control will continue with 2 additional trials for ignition. The Inducer and Blower motors will continue running during the flame out scenario. Flame out of sequence Flame out of sequence represents a scenario when flame is sensed while the gas valve is de-energized. The Inducer and Blower motors will be engaged (if not already running) and continue running for as long as the fault condition is present. ICM2812 TIMING Input 18-30 VAC, 60Hz Ignition Activation Period 3 seconds Ignitor Warm-up 19 seconds Inducer Inter-purge 60 seconds Inducer Post-Purge 25 seconds Inducer Pre-purge 30 seconds Trial for Ignition 4 seconds Trials 3 Cool Blower OFF delay 45 seconds Cool Blower ON delay 6 seconds Heat Blower OFF delay 100/150 seconds Heat Blower ON delay 30 seconds Lockout 60 minutes FAULT RECALL BUTTON To review the fault history; press and hold the Fault Recall button and release once the LED goes out. The previous five fault codes will be displayed. The LED will turn off momentarily and then go solid after the last fault has been displayed. The ICM2812 will not respond to thermostat calls while the fault history is being displayed. To clear the fault history; press and hold the Fault Recall button and release once the LED starts flashing. The LED will turn off momentarily and then go solid after the fault history has been cleared. The fault history will not erase while the ICM2812 is performing a heating or cooling call. LED FAULT CODES LED Status Description Trouble Shooting Tips ON Normal operation N/A OFF Control board failure Check for proper input voltage and check the fuse; if not resolved replace the control. 1 Ignition failure (soft lockout) Clean or replace the flame sensor, check the igniter for proper operation & input voltage, check the transformer's common is grounded to earth ground. 2 Pressure switch stuck closed Check for contaminated or defective pressure switch. 3 Pressure switch stuck open Check for obstructed pressure switch tubing or defective pressure switch. Check for oxidation on terminals, broken wires, or defective inducer motor. 4 Limit switch fault Checked for blocked airflow, blocked duct work, and dirty filter. Check or replace high limit switch if defective. 5 Flame out of sequence Check for intermittent or defective gas valve and check for dirty or defective flame sensor. 6 Roll out switch fault Check for a cracked heat exchanger, defective rollout switch , broken wires on the roll out switch, or replace roll out switch if required. 7 Weak flame Weak flame is caused by carbon build up on the flame sensor, poor grounds, or improper placement of the flame sensor. Clean or replace the flame sensor, reassure grounds, ensure the flame sensor is fully enveloped in the flame. 8 Mis--wired gas valve Check for shorted or mis--wired gas valve, check harness wires for any shorts or breaks, and check the pressure switch for proper operation. 9 Unused N/A 1o Hot and neutral reversed Check for proper polarity of the incoming voltage on the primary and secondary sides of the transformer. 11 Brownout A brownout fault indicates a low voltage condition. Check the voltage on the primary and secondary sides of the transformer and ensure there is no excessive load on the transformer. ICM2812-KIT CROSS REFERENCE The ICM2812 is a board only replacement for the White-Rodgers universal control board packaged with the 50M56U-843. The ICM2812-KIT includes the replacement board and wiring adapters/harnesses that allow it to also be a replacement for all of the furnace board models listed in the table below. See Noe 1ICM2812-KIT CROSS REFERENCE WIRING DIAGRAM ICM Controls ICM2812 Universal Replacement Furnace Control Board Kit - DIAGRAMLegend: ICM Controls ICM2812 Universal Replacement Furnace Control Board Kit - Icon 1Low voltage (24 VAC) ------High voltage (120 VAC) N.C. = Normally closed switch N.O. = Normally open switch 12-Pin Connections 1 = Limit switch Out 2 = Low gas valve 3 = 24 VAC hot (R) 4 = Pressure switch Out 5 = Rollout switch Out 6 = 24 VAC common (C) 7 = Limit switch In 8 = Earth ground 9 = Gas valve common 10 = Pressure switch In 11 = Rollout switch In 12 = High gasvalve 4-Pin Connections 1 = Inducer blower 2 = Hot Surface Ignitor (HSI) 3 = Inducer blower neutral 4 = Hot Surface Ignitor (HSI) neutral Note 1: For American Standard/Trane, York PCLU and York P3UR furnaces: Install the black wire labeled “10” from pin 5 to pin 11 of the 12-pin harness which is connected to the furnace. Note 2: There are some Rheem/RUUD furnace models which performed flame sense differently. Please read the information below before testing the furnace. Note 3: For Nordyne furnaces, ICM2812-KIT will only be compatible with 120VAC models. Rheem/RUUD furnaces without a separate flame sensor will require the purchase of a Rheem flame sensor kit (62-24044-71) to be wired to pin 7 of the 9-pin harness which is connected to the furnace. Rheem/RUUD furnaces with a separate flame sensor which is NOT routed through the 9-pin harness will require removal of the flame sensor wire from the existing connection and rewiring it to pin 7 of the 9-pin harness which is connected to the furnace. Rheem/RUUD furnaces which have a separate flame sensor already routed to pin 7 of the 9-pin harness will not require this modification. Connect the other end of the furnace harness into the ICM2812 harness labeled “2”, connect the other end of this harness to the ICM2812 circuit board and connect the orange wire to the “FS” (flame sensor) terminal. ICM Controls Logo7313 William Barry Blvd., North Syracuse, NY 13212 www.icmcontrols.com 800.365.5525 LIAF268-2 Documents / Resources ICM Controls ICM2812 Universal Replacement Furnace Control Board Kit [pdf] Instruction Manual ICM2812 Universal Replacement Furnace Control Board Kit, ICM2812, Universal Replacement Furnace Control Board Kit, Furnace Control Board Kit, Board Kit, Kit Documents - icm-controls,icm controls – ICM2812 [pdf] Troubleshooting Guide Specifications Sell Sheet Edmondson Supply ICM Controls ICM2812 KIT Universal Furnace Control Board icmcontrols 2021 01 ||| A P P L I C AT I O N S : ICM2812-KIT Universal Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal board only replacement for the WhiteRodgers 50... lang:en score:44 filesize: 1.88 M page_count: 3 document date: 2022-04-29 [pdf] Troubleshooting Guide Specifications Sell Sheet Edmondson Supply ICM Controls ICM2812 Universal Furnace Control Board board only Replacement for White Rodgers 50M56U 843 2 icmcontrols 2020 12 ||| A P P L I C AT I O N S : ICM2812 Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal board only replacement for the WhiteRodgers 50M56U-843 and m... lang:en score:43 filesize: 1.2 M page_count: 1 document date: 2022-04-29 [pdf] Troubleshooting Guide Specifications Datasheet ICM Controls ICM2812 KIT Universal Replacement Board for White Rodgers 50M56U 843 Jackson Systems Data Sheet jacksonsystems 2021 10 ||| ICM2812 FURNACE CONTROL MODULE Features Hot Surface Ignition HSI control board Microprocessor-based Monitors timing, trial for ignition, system switches, flame sensing and lockout 100 lockout safety feature Compatible with LP or Natural Gas LED indication for status and fault codes to aid i... lang:en score:43 filesize: 575.17 K page_count: 3 document date: 2020-09-09 [pdf] Troubleshooting Guide Specifications ICM2812ICM2812□ Redundant gas valve design conforms to ANSI Z21 20 BUILT TO THE HIGHEST Download the ICM Controls app for full cross reference information The ICM2812ICM2812cdn lsicloud net pandhwhsal documents ICM2812cdn ICM2812 ||| A P P L I C AT I O N S : ICM2812 Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal board only replacement for the WhiteRodgers 50M56U-843 and m... lang:en score:42 filesize: 1.2 M page_count: 1 document date: 2022-04-29 [pdf] Reference Guide Guide ICM CONTROLS CROSS REFERENCE GUIDE FENWAL 35 725205 521 ICM2910 205 725206 515 206 Honeywell Cam Stat Fenwal Penn Johnson Robertshaw and more ICMControls 00343 1 2 OTHER1 media distributordatasolutions 4855 xlsx trimble d869c8d2f59ed1dc23977be8a0f7699b71c8cb89 ||| ICM CONTROLS CROSS REFERENCE GUIDE REPLACEMENT MODEL ICM P/N MARS: 32395 SUPCO: TD32 BYPASS TIM ... 62-120, 50A62-121, 50A62-820, 21D83M-843, 50A66-122, 50A66-123 ICM2813 WHITE-RODGERS: 50M56U-843 ICM2812, ICM2812-KIT WHITE-RODGERS: 50T35-730, 50T35-743 ICM280 YORK: S1-331-03010000, S1-331-029... lang:i-klingon score:42 filesize: 370.02 K page_count: 2 document date: 2023-10-19 [pdf] Troubleshooting Guide Specifications Specification Sheet ICM Controls ICM2812 KIT Universal Replacement Furnace Control Board Kit skipthewarehouse index route extension module mmos attachmanager getfile product attach file id 17481 ||| A P P L I C AT I O N S : ICM2812-KIT Universal Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal board only replacement for the WhiteRodgers 50... lang:en score:41 filesize: 1.61 M page_count: 3 document date: 2023-05-23 [pdf] User Manual Installation Guide Troubleshooting Guide Documentation Guide Application Guide Diagram Label Installation Manual ICM Controls ICM2812 KIT Universal Replacement Furnace Control Board Kit skipthewarehouse index route extension module mmos attachmanager getfile product attach file id 17480 ||| INSTALLATION, OPERATION APPLICATION GUIDE For more information on our complete range of American-made products plus wiring diagrams, troubleshooting tips and more, visit us at www.icmcontrols.com ICM2812 and ICM2812-KIT Hot Surface Ignition HSI Control Board REPLACES See pages at end of this i... lang:en score:41 filesize: 800.81 K page_count: 2 document date: 2022-11-17 [pdf] ICM CONTROLS HVAC Catatlog LIC037 2 Web icmcontrols 2022 12 ||| HVAC-R Market Engineering. Manufacturing. Innovation. ICM Controls is a leader in the manufacture ... 30 ICM2810..................................... 30 ICM2811...................................... 31 ICM2812..................................... 31 ICM2812-KIT................................ 28 ICM28... lang:en score:40 filesize: 5.46 M page_count: 44 document date: 2022-12-15 [pdf] Catalog Catalogs ICM Controls LIC037 6 HVACR 07 24 web icmcontrols 2024 ||| HVAC-R Market Engineering. Manufacturing. Innovation. ICM Controls is a leader in the manufacture ... 30 ICM2810..................................... 31 ICM2811...................................... 31 ICM2812-KIT................................ 28 ICM2813..................................... 31 ICM29... lang:en score:40 filesize: 10.26 M page_count: 44 document date: 2024-07-24 [pdf] Troubleshooting Guide Specifications ICM2812 KITSell Sheet v1715151421662cdn accentuate io 8420790206714 11562980147290 Sell v1715151421662 KITICM2812 v1715151421662ICM2812 KIT Specscdn v1715151421662manuals totalhomesupply manuals Specs KITThe is a universal board only replacement for the White Rodgers 50M56U 843 and more than 150 competitive part numbers Download ICM Controls app ICM2812 lsicloud net pandhwhsal documents KITcdn ||| ||| A P P L I C AT I O N S : ICM2812-KIT Universal Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal bo ||| A P P L I C AT I O N S : ICM2812-KIT Universal Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal bo A P P L I C AT I O N S : ICM2812-KIT Universal Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal board only replacement for the WhiteRodgers 50... lang:en score:39 filesize: 1.61 M page_count: 3 document date: 2023-05-23 [pdf] Catalog ICM CONTROLS Controls HVAC R Catalog Web v3 icmcontrols 2021 09 ||| HVAC-R Market NOTES The name to know for controls. ICM Controls is a leader in the manufacture o ... 30 ICM2810..................................... 30 ICM2811...................................... 31 ICM2812..................................... 31 ICM2812-KIT................................ 31 ICM28... lang:en score:38 filesize: 6.06 M page_count: 52 document date: 2021-09-10 [pdf] Reference Guide Guide icmcontrols 2022 02 ICM CONTROLS CROSS REF LIAF309 1 REFERENCE GUIDE ™ Icm cross reference chart Keyword Found Websites Listing Suggestions bypass timers mars 32395 icm175 supco td32 delay on make a 7061 icm103 eac 701 adj icm102 diversified asc 200 icm150 ac 800 gemline 1c213 1c310 ice o matic td3001a 28 feb — 20222 pagine ||| ICM CONTROLS CROSS REFERENCE GUIDE REPLACEMENT MODEL ICM P/N MARS: 32395 SUPCO: TD32 BYPASS TIM ... 62-120, 50A62-121, 50A62-820, 21D83M-843, 50A66-122, 50A66-123 ICM2813 WHITE-RODGERS: 50M56U-843 ICM2812, ICM2812-KIT WHITE-RODGERS: 50T35-730, 50T35-743 ICM280 YORK: S1-331-03010000, S1-331-029... lang:i-klingon score:37 filesize: 229.89 K page_count: 2 document date: 2022-02-17 [pdf] ICM2812 KIT ICM CONTROLS LIAF321 CRG icmcontrols 2021 01 ||| ICM2812-KIT Cross Reference See Note 1 The ICM2812 is a board only replacement for the White-Rodgers universal control board packaged with the 50M56U-843. The ICM2812-KIT includes the replacement board and wiring adapters/harnesses that allow it to also be a replacement for all of the furnace boar... lang:nl score:37 filesize: 268.73 K page_count: 2 document date: 2022-12-09 [pdf] Catalog HVAC R Market 6 янв 2025 г — From concept to prototype production The ICM Controls manufacturing plant located in North Syracuse New York is one of the most Catalog Misc sidharvey documents ||| HVAC-R Market Engineering. Manufacturing. Innovation. ICM Controls is a leader in the manufacture ... 30 ICM2810..................................... 31 ICM2811...................................... 31 ICM2812-KIT................................ 28 ICM2813..................................... 31 ICM29... lang:en score:36 filesize: 10.05 M page_count: 44 document date: 2025-01-06 [pdf] ICM Controls Cross Reference Emerson Climate Technologies Electric White Rodgers Equivalent OEM Part Direct Universal ICM280 50T35 743 50M56U 843 Goodman B1809906 B1809908 B1809910 B1809913 B1809913S Control ICM283 50E47 Honeywell S8910U1000 Robertshaw HS780 50F47 ICM290A 50D50 S8610U3009 compatible Camstat Fenwal HSC Penn Johnson UTEC 1012 933D Texas Instruments 41F 5 icm controls cross reference en 5124712 climate emerson documents ICM Controls Cross Reference INTEGRATED FURNACE CONTROLS ICM Control White-Rodgers Equivalent Direct Universal ICM280 ICM281 ICM282A ICM284 ICM286 ICM287 ICM288 ICM289 ICM291 ICM292 ICM2801 ICM2804 ICM2805A ICM2807 ICM2808 ICM2810 ICM2811 ICM2812-KIT 50T35-743 50M56D-751 50M56U-751 50A55-743 ... lang:en score:35 filesize: 123.93 K page_count: 2 document date: 2021-01-08 [pdf] ICM Controls New Best Sellers! 28 ago 2022 — 20224 pagine Heating Season d24 webopt icmcontrols 08 ||| GET AHEAD OF THE WINTER WITH ICM Controls New Best Sellers CONTACT YOUR LOCAL DISTRIBUTOR FOR PRESEASON SPECIALS ICM2812-KIT Universal Furnace Control Board Replacement for the White-Rodgers 50M56U-843 and more than 150 Furnace Boards including models from Honeywell, Johnson Controls, Robertshaw... lang:en score:35 filesize: 1023.34 K page_count: 4 document date: 2022-08-15 [pdf] ICM2812 Kit Universal FCB PR DAF6BF72ddk BADJm7Wuql8 Shreya Vardekar 2 icmcontrols 2024 01 ||| Introducing the ICM2812-Kit, the all-new Universal OEM Replacement Control from ICM Controls A reputation-driven electronic control manufacturer, ICM Controls, is set to release the ICM2812-kit, an adaptable OEM Replacement Control Board an excellent van stock. FOR IMMEDIATE RELEASE Chicago, IL- ... lang:en score:34 filesize: 823.7 K page_count: 3 document date: 2024-01-19 [pdf] Troubleshooting Guide Specifications ICM2812 AND KIT Sell Sheet icmcontrols 2020 12 ||| A P P L I C AT I O N S : ICM2812 AND ICM2812-KIT Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV FEATURES Furnace control module Hot Surface Ignition HSI control board Micr... lang:en score:34 filesize: 648.98 K page_count: 1 document date: 2021-10-28 [pdf] Edmondson Supply ICM Controls ICM2812 KIT Universal Furnace Control Board cross ref icmcontrols 2021 01 u003ecross ||| Manufacturer Amana/Goodman Amana/Goodman Amana/Goodman Amana/Goodman Amana/Goodman Amana/Goodman Ama ... vcon/Luxaire/York Coleman/Evcon/Luxaire/York Coleman/Evcon/Luxaire/York Coleman/Evcon/Luxaire/York ICM2812-KIT CROSS REFERENCE Part Number 10207701 10207704 10207706 10207710 10207714 10207717 10207... lang:nl score:33 filesize: 144.41 K page_count: 2 document date: 2021-11-17 [pdf] Reference Guide Guide ICM Controls ISO certified Electronics Manufacturing CompanyICM CompanyLIAF309 2 CrossRefGuideLIAF309 CrossRefGuidedropbox scl fi 1l9x9yq5ahrvvborhtg15 LIAF309 CrossRefGuide rlkey 7dpfl61psez5x1ejwy1xopchn dl 0dropbox ||| ICM CONTROLS - CROSS REFERENCE GUIDE REPLACEMENT MODEL ICM P/N MARS: 32395 SUPCO: TD32 BYPASS TI ... 62-120, 50A62-121, 50A62-820, 21D83M-843, 50A66-122, 50A66-123 ICM2813 WHITE-RODGERS: 50M56U-843 ICM2812, ICM2812-KIT WHITE-RODGERS: 50T35-730, 50T35-743 ICM280 YORK: S1-331-03010000, S1-331-029... lang:i-klingon score:32 filesize: 230.72 K page_count: 2 document date: 2023-04-11 [pdf] Installation Guide Troubleshooting Guide Specifications Documentation Guide Application Guide Diagram Label ICM2812 ICM Controls Dec 31 2020 — products plus wiring diagrams troubleshooting tips and more visit Cooling A cooling call from the thermostat will energize blower motor at high LIAF268 1 icmcontrols 12 ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 amp 24 VAC Inducer draft motor: 2.2 FLA 12... lang:en score:31 filesize: 484.27 K page_count: 6 document date: 2020-09-02 [pdf] Cross Reference Replacements ICM Controls ICM2812 KIT Universal Replacement Furnace Control Board Kit skipthewarehouse index route extension module mmos attachmanager getfile product attach file id 17482 ||| ICM2812-KIT Cross Reference See Note 1 The ICM2812 is a board only replacement for the White-Rodgers universal control board packaged with the 50M56U-843. The ICM2812-KIT includes the replacement board and wiring adapters/harnesses that allow it to also be a replacement for all of the furnace boar... lang:nl score:31 filesize: 268.74 K page_count: 2 document date: 2022-12-09 [pdf] Troubleshooting Guide Specifications ICM2812 KIT Sell Sheet LIS506 icmcontrols 2021 01 ||| A P P L I C AT I O N S : ICM2812-KIT Universal Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal board only replacement for the WhiteRodgers 50... lang:en score:30 filesize: 1.61 M page_count: 3 document date: 2023-05-23 [pdf] Troubleshooting Guide Specifications ICM2812 KIT AMRE Supply□ Redundant gas valve design conforms to ANSI Z21 20 BUILT TO THE HIGHEST STANDARDS Page 2 icmcontrols 1 800 365 5525 info@icmcontrols 7313 ICM2812 Sell sheetamresupply file 219900 inline Y srsltid AfmBOoq9kVa9HcxpcSLYmrsf15E88uww29E4JR27SgVZvUzLxRYFw1LE ||| A P P L I C AT I O N S : ICM2812-KIT Universal Furnace Control Board Scan to see a full specifications, installation and agency certification information. APPLIANCE ELECTRICAL HVAC/R MARINE POOL SPA RV OVERVIEW The ICM2812 is a universal board only replacement for the WhiteRodgers 50... lang:en score:30 filesize: 1.88 M page_count: 3 document date: 2022-04-29 [pdf] Troubleshooting Guide Specifications Datasheet Data SheetICM Controls ICM2812 KIT Replacement Board for White Rodgers 50M56U 843ICM2812 Sheetjacksonsystems 2024 07 Sheet Jackson SystemsData SheetD341396P04 American Standard Trane D341396P05 D34139P03 Carrier HK42FZ004 HK42FZ007 HK42FZ008 CarrierICM SheetICM2812 srsltid AfmBOopiAHK8id8pGPz8bmY2tzJH9m71H4AX6ystxrumw2nOn8YrOAWFjacksonsystems CarrierThe is a universal board only replacement the Kit with harness Conforms to UL STDs 60730 1 and 2 5 ICM Sheet9434014 7933503 specificationICM2812 AfmBOopiAHK8id8pGPz8bmY2tzJH9m71H4AX6ystxrumw2nOn8YrOAWFfergusonprod bigcontent io v1 static 9434014 specificationjacksonsystems ||| ||| ICM2812 FURNACE CONTROL MODULE Features Hot Surface Ignition HSI control board Microprocessor-based Monitors timing, trial for ignition, system switches, flame sensing and lockout 100 lockout safety feature Compatible with LP or Natural Gas ||| ICM2812 FURNACE CONTROL MODULE Features Hot Surface Ignition HSI control board Microprocessor-based Monitors timing, trial for ignition, system switches, flame sensing and lockout 100 lockout safety feature Compatible with LP or Natural Gas ICM2812 FURNACE CONTROL MODULE Features Hot Surface Ignition HSI control board Microprocessor-based Monitors timing, trial for ignition, system switches, flame sensing and lockout 100 lockout safety feature Compatible with LP or Natural Gas LED indication for status and fault codes to aid i... lang:en score:27 filesize: 575.17 K page_count: 3 document date: 2020-09-09 [pdf] Catalog Catalogs ICM ControlsCatalogs ControlsICM OEM Catatlog LIC042 1 WebICM Webdropbox scl fi khh9bx27w9gqp0evt7hmv Web rlkey 31yum3d9gjbypkqtb9j92sh5a dl 0dropbox ||| OEM Market Engineering. Manufacturing. Innovation. ICM Controls is a leader in the manufacture of ... r LH33WP003/3A ICM291 Carrier HK42FZ004, HK42FZ007, HK42FZ008, HK42FZ009, HK42FZ011, HK42FZ016 ICM2812-KIT G951ADB-1401 C , G951ADB1402, G951ADB-1403, G951AEB-1403, 265901, 265902, 539617, 525... lang:en score:24 filesize: 14.96 M page_count: 28 document date: 2023-08-15 [pdf] Catalog Catalogs ICM ControlsCatalogs ControlsICM LATAM Catalog SPA LIC043 WebICM Webdropbox scl fi jl6grlzcz3ofhi5w65bew Web rlkey mt45xen9ldoh449jpqv3ohl10 dl 0dropbox ||| Mercado latinoamericano ICM Controls / LATAM ICM - FABRICADO EN LOS EE. UU. Ingenier a. Manufac ... 21 ICM1502..................................... 21 ICM1503...................................... 21 ICM2812-KIT................................ 20 ICM2918..................................... 21 UMSR-... lang:es score:24 filesize: 3.41 M page_count: 24 document date: 2023-09-14 [pdf] LIC037 3 HVACR web icmcontrols 2023 08 ||| HVAC-R Market Engineering. Manufacturing. Innovation. ICM Controls is a leader in the manufacture ... 32 ICM2810..................................... 32 ICM2811...................................... 32 ICM2812-KIT................................ 30 ICM2813..................................... 32 ICM29... lang:en score:23 filesize: 5.54 M page_count: 45 document date: 2023-08-14 [pdf] Specifications WWW IC M C ONTR OLS O 9 SPECIFICATIONS Voltage 24 VAC 18 30 60 Hz Line voltage 208 230 Power cons 0 3A plus Gas valve current @ ICMControls 00211 28 CAT media distributordatasolutions 4855 xlsx trimble 9609423ca403bca5622ef5aaf994fd3056951acb ||| ICM Controls / HVAC-R REPLACEMENT MODEL ICM P/N FAN COIL RELAY CONTROL BOARDS N/A ICM6202 FURN ... 62-120, 50A62-121, 50A62-820, 21D83M-843, 50A66-122, 50A66-123 ICM2813 WHITE-RODGERS: 50M56U-843 ICM2812, ICM2812-KIT WHITE-RODGERS: 50T35-730, 50T35-743 ICM280 YORK: S1-331-03010000, S1-331-029... lang:i-klingon score:22 filesize: 346.94 K page_count: 2 document date: 2022-08-27 [pdf] WWW IC M C ONTR OLS O 9 FEATURES APPLICATION Controls gas valve inducer draft motor circulating blower and hot surface ignitor Monitors timing trial for ignition ICMControls 00211 30 CAT media distributordatasolutions 4855 xlsx trimble a28ae31f6f1d31f8f95c480499b57e5320d1da84 ||| ICM Controls / HVAC-R REPLACEMENT MODEL ICM P/N FAN COIL RELAY CONTROL BOARDS N/A ICM6202 FURN ... 62-120, 50A62-121, 50A62-820, 21D83M-843, 50A66-122, 50A66-123 ICM2813 WHITE-RODGERS: 50M56U-843 ICM2812, ICM2812-KIT WHITE-RODGERS: 50T35-730, 50T35-743 ICM280 YORK: S1-331-03010000, S1-331-029... lang:i-klingon score:22 filesize: 342.58 K page_count: 2 document date: 2022-08-27 [pdf] ICMHVACCatatlog LIC037 1 Web cat wsconet Documents action view ||| HVAC-R Market NOTES The name to know for controls. ICM Controls is a leader in the manufacture o ... 30 ICM2810..................................... 30 ICM2811...................................... 31 ICM2812..................................... 31 ICM2812-KIT................................ 31 ICM28... lang:en score:22 filesize: 4.09 M page_count: 52 document date: 2022-10-27 [pdf] WWW IC M C ONTR OLS O 9 FEATURES APPLICATION Control Gas valve ignitor blower motor inducer humidifier and air cleaner Microprocessor based ICMControls 00211 27 CAT media distributordatasolutions 4855 xlsx trimble 874c04f217f629673d764cc00e2290fbafdc4f96 ||| ICM Controls / HVAC-R REPLACEMENT MODEL ICM P/N FAN COIL RELAY CONTROL BOARDS N/A ICM6202 FURN ... 62-120, 50A62-121, 50A62-820, 21D83M-843, 50A66-122, 50A66-123 ICM2813 WHITE-RODGERS: 50M56U-843 ICM2812, ICM2812-KIT WHITE-RODGERS: 50T35-730, 50T35-743 ICM280 YORK: S1-331-03010000, S1-331-029... lang:i-klingon score:21 filesize: 275.12 K page_count: 2 document date: 2022-08-27 [pdf] User Manual Installation Guide Troubleshooting Guide Specifications Documentation Guide Application Guide Diagram Label ICM2812 Jackson SystemsExamine control and box to check for water stains 9 Make repairs if Heil Quaker ICP Thermo Products Whirlpool 1010806 5 6 International ICM2812 Application Guidejacksonsystems 2024 07 Guide srsltid AfmBOoowxoPudbO46Ms8U2G2CmYzgPSJAZmo1zEGcsMC5VKcRreSqKXZ SystemsICM2812 International Disconnect line voltage blower electronic air cleaner wires equipped transformer Note 1 For American Standard Trane York PCLU York ICM2812 GuideICM2812 AfmBOoowxoPudbO46Ms8U2G2CmYzgPSJAZmo1zEGcsMC5VKcRreSqKXZjacksonsystems AfmBOoop4jfzpA2O0NFm4rCRmimXiT0 ntCynfaE5UXdDu61D13HPNoa York There will be 2 more attempts ignite after the 60 seconds delay before S1 03100662000 Coleman Evcon Luxaire 03101250000 Coleman ICM2812 ntCynfaE5UXdDu61D13HPNoajacksonsystems AfmBOopKN vLww1ry7q7VRwrdnH3I9hKucAVtfOzEknd4i8Ex0 sgbXI SystemsApplication GuideExamine Coleman ICM Controls KIT Replacement Board White Rodgers 50M56U 843ICM2812 sgbXIjacksonsystems Coleman D341396P04 D341396P05 D34139P03 Carrier HK42FZ004 11 12 HK42FZ007 CarrierICM AfmBOooPVVPa71srkt0BPxWVgGnh3g3QaFUnPeEVBc8LLhEGnXfx1JWMjacksonsystems 2023 08 AfmBOopOgxaa4mcynG6VH6xJGOsLBGpgI27KbwOp9cNjLeBZMxSwxI7 CarrierESD damage can also prevented by using an ESD service kit Specifications Control 24 VAC 18 30 Hz Line 120 HzICM AfmBOopS5Lh0z6qusfrixjaHDopQfStYO 1z8UFIegdzuydRa4IROcTWjacksonsystems AfmBOopOgxaa4mcynG6VH6xJGOsLBGpgI27KbwOp9cNjLeBZMxSwxI7jacksonsystems AfmBOoqr WV8KbKPBrxaJUiYO H6qhppGVLqzsHx7T6c7R2uI8rDzoTd H6qhppGVLqzsHx7T6c7R2uI8rDzoTdjacksonsystems AfmBOorFZH21 BLCe64nsG5HxSHE2HPWKa154bBq1lzLUwyji9QIiLqL HzWhite 50A50 110 111 112 405 406 407 6ICM AfmBOooOh1sbKzt76S hLyC9E4nCqEr6MUeLHAhl7mxWjUDCHeQCjGK5jacksonsystems 6White AfmBOoqomW L2mZA4rP8IwocUNck1egp5UgPSA6rXHeKybNNPr945TpWjacksonsystems BLCe64nsG5HxSHE2HPWKa154bBq1lzLUwyji9QIiLqLjacksonsystems AfmBOoqGIreuuK2oKHUpIcyhuNzqwp PShH1jgdiQagM49XqnQWzhb1t 50A55 476 480 486 AfmBOorrKtMKfuDXmgfQF 9zHw8WcwyqTY C0DoT3bvixxIjcMEB fWyjacksonsystems PShH1jgdiQagM49XqnQWzhb1tjacksonsystems AfmBOooZUGGl GaEnDjjH2hCOc4ONrnLHQAFjh6j7f57Pr2vDYXr PRH PRHjacksonsystems AfmBOorTnk 438j6XCQFLe6kQbbUtrbs TfVS6YBgrj7RYuW6Vyn4IgU TfVS6YBgrj7RYuW6Vyn4IgUjacksonsystems AfmBOorek9dFmsom6djz8khoSiixtvYAclUepQTpWFjM5 LQTPKCVScT LQTPKCVScTjacksonsystems AfmBOoolV 1qE0Amy96u89RSqnRDGzUuIbtTCLLQPZgb9 29NcRrp6Ro 29NcRrp6Rojacksonsystems AfmBOor0zG sZ3uF8AhoDa ZHQCOhoxFFz BDGsmTn55KKfCSDDTwF37 571 743 AfmBOorWO4ykirx APs1lyYOQ OTUYr4EfXjFdU 4vOKqqc0UobWnEKajacksonsystems BDGsmTn55KKfCSDDTwF37jacksonsystems AfmBOoqT agwndrQHGy p5sdu4g HUtGGL5P FK jb xTlWIAkjQkm7a xTlWIAkjQkm7ajacksonsystems AfmBOook3RS0MM6yictflhqCP7IYmC2VsqJH8h837XfiPLSRc1ldrckW AfmBOook3RS0MM6yictflhqCP7IYmC2VsqJH8h837XfiPLSRc1ldrckWjacksonsystems AfmBOopbhr1Q3sDGM7TCfBV9mKmd9uAR8RlwZRmO4gWfHhsZZaPH7TFv AfmBOopbhr1Q3sDGM7TCfBV9mKmd9uAR8RlwZRmO4gWfHhsZZaPH7TFvjacksonsystems AfmBOopDIdDTwPyw6AmN6UzjDsJpe1tZr2Ay3mXG4EQ7gxFdKB1BqKki AfmBOopDIdDTwPyw6AmN6UzjDsJpe1tZr2Ay3mXG4EQ7gxFdKB1BqKkijacksonsystems AfmBOoo7bsYWi3jcFrHX9mxsMkyiwMQjegDCr2qm3BdZYv5kzeSMbRA6 AfmBOoo7bsYWi3jcFrHX9mxsMkyiwMQjegDCr2qm3BdZYv5kzeSMbRA6jacksonsystems AfmBOormEaDuXm5ZbBYgfjZ58EHf u7s0nq34tSXGs7E8uOj20xzi8xD 6The has incorporated LED diagnostics assist in troubleshooting Fault code information found this application guide Please keep this ICM AfmBOor8kAmVHhz5ag17uK yuuMvD1J9EIa7wvCNWqEKXb9YJcSFowZyjacksonsystems u7s0nq34tSXGs7E8uOj20xzi8xDjacksonsystems AfmBOoqSMvHWF8B5ADwQMOoPOI9TZwjbJRZ8Z7vrnEAkwKlpq 8icEGK 8icEGKjacksonsystems AfmBOopVeoT SHwY3sC8Yi5lh9BcdeIxdQb1KZsV4VwYNBI9iH4J5ABY SHwY3sC8Yi5lh9BcdeIxdQb1KZsV4VwYNBI9iH4J5ABYjacksonsystems AfmBOorukdbLxCjUpcTR2vvR2M5d6OBHhwq1uihJCdpope0sTXkzSjHG this Fault with furnace installation manual future referenceICM AfmBOoo77L1izWqWjUerUeg87xbdMg09r7FBFDJhX2Dm9jdGF5DBTfDBjacksonsystems referenceThe AfmBOoqjQ xiX 4I gtHkgRYYnty6qDSS0wBTpzaayPFgLd38YWJ6hGSjacksonsystems this The AfmBOop9yxrDGKNalbYs7ZnEOY2V62 kpdlNEXEIKOzYqKaWjiAG uajjacksonsystems AfmBOorukdbLxCjUpcTR2vvR2M5d6OBHhwq1uihJCdpope0sTXkzSjHGjacksonsystems ||| ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ||| ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 a ICM2812 Hot Surface Ignition HSI Control Board Specifications Control voltage: 24 VAC 18-30 VAC , 60 Hz Line voltage: 120 VAC, 60 Hz Operating temperature: -40to 175F -40to 80C Outputs HSI Hot Surface Ignitor: 6 amp 120 VAC Gas Valve: 1.5 amp 24 VAC Inducer draft motor: 2.2 FLA 12... lang:en score:21 filesize: 484.27 K page_count: 6 document date: 2020-09-02 [pdf] ICM Replacement Furnace Controls v2 icmcontrols 2021 11 ||| LOW COST, HIGH PERFORMANCE OEM Replacement Boards From ICM Controls ICM2812-KIT Universal Furnace Control Board Replacement for the White-Rodgers 50M56U-843. Replaces more than 150 Furnace Boards including models from Honeywell, Johnson Controls, Robertshaw, White-Rodgers, Fenwal, HSC, Camstat and m... lang:en score:17 filesize: 1.69 M page_count: 4 document date: 2021-11-22 tags: Board Kit, Furnace Control Board Kit, ICM CONTROLS, ICM2812, ICM2812 Universal Replacement Furnace Control Board Kit, Kit, Universal Replacement Furnace Control Board Kit, | |||
| ICM furnace control boards Canada. we carry control boards available online in Canada. | |||
| You will find tankless water heater repair services in this link for Toronto, Scarborough, Oakville, Burlington, Stouffville, Mississauga, Milton, Hamilton. They do repair and maintenance on all these tankless hot water heater manufactures, Rheem, Rinnai , Navien, Takagi , Bosch , Leading tankless water heater manufacturers for 2026 include Rinnai, Navien, Rheem, and Noritz, recognized for high efficiency and reliability. Other top brands offering gas or electric units include A.O. Smith, Bosch, Bradford White, EcoSmart, Eccotemp, and Stiebel Eltron. Leading tankless water heater manufacturers for 2026 include Rinnai, Navien, Rheem, and Noritz, recognized for high efficiency and reliability. Other top brands offering gas or electric units include A.O. Smith, Bosch, Bradford White, EcoSmart, Eccotemp, and Stiebel Eltron. These manufacturers specialize in providing on-demand, energy-efficient hot water for residential and commercial applications. Top Tankless Water Heater Manufacturers Rinnai: A top industry leader for gas and condensing models, known for durability and high-performance, rated 5 stars by Modernize. Navien: Renowned for high-efficiency condensing technology, high flow rates (up to 9.5 GPM), and ComfortFlow recirculation. Rheem: Offers a wide range of gas and electric models, known for reliability and smart features like Wi-Fi connectivity. Noritz: Known for high-efficiency, durable units with up to 25-year heat exchanger warranties and superior flow rates up to 9.8 GPM. A.O. Smith: Features durable, high-efficiency models with advanced,, scale-prevention technology. Bosch: Offers compact, highly efficient, and reliable tankless models. Bradford White: A trusted manufacturer for both gas and electric, high-quality, professional-grade models. EcoSmart: Specializes in energy-efficient electric tankless heaters suitable for eco-conscious consumers. Stiebel Eltron: Known for reliable, German-engineered electric tankless units. Eccotemp: Offers affordable, versatile gas and electric options, often used for smaller, specialized, or portable applications. Other Notable Manufacturers Eemax: Specializes in electric tankless heaters. Intellihot: Focuses on heavy-duty, high-efficiency gas units. State Water Heaters: Provides a range of residential and commercial units. Hubbell: Offers specialized, durable heating solutions. RV-Specific Tankless Manufacturers Suburban, Girard, Furrion, Fogatti, Dometic: Leading brands specifically for RV applications. Key Considerations When choosing a manufacturer, evaluate based on energy efficiency (EF), maximum flow rate (GPM), and warranty length, which often ranges from 10 to 15 years for premium brands. |
CSR-U1